Loading... Please wait...

Wilton C1 Combonation Bench Vise with 4-1/2 x 1-1/4 Jaws

Hover over image to zoom

  • Image 1
  • Image 2
  • Image 3
  • Image 4
  • Image 5
  • Image 6
  • Image 7
  • Image 8
  • New jaws and Pipe jaws.
  • Image 10
  • New horseshoe washer and handle.
  • Image 12
  • New end cap.
  • Refinished anvil.
  • Battle scars.
  • New Swivel Clamps.
  • Image 17
  • Replaced 1/4 pin with this 5/16 setscrew machined down to a 1/4 inch.  The Static jaw support was tapped t a 5/16:18 thread.
  • Date code is 4-1986
  • Drilling pin holes for the Pipe Jaws.
  • Drilling, reaming and tapping original pin hole, note the wood wedge to locate the nut.
$420.00
Shipping:
$70.00 (Fixed shipping cost)

Sorry but this item is currently unavailable. Please check back at a later stage.

 Product Description

Here is a perfect sized vise for your workbench, not to big and not to small and having the option to hold pipes. This Wilton C1 (Combination Pipe Vise)  comes with new 4-1/2 jaws and a new set of Pipe jaws. On the pipe jaws I did not like the clip design so I added four custom made pins and pinned the pipe jaws in place, much easier to take apart and finding another clip if broken or lost is harder to find. 

I repositioned the groove in the spindle that the Horseshoe washer rides in, I like vises with minimal backlash and this guy has very little backlash. I am happy with the fix I did. I also installed a new custom made Horseshoe washer 2-5/8 x 3/16 made from A2 Tool Steel and precision ground flat. I redesigned the washer screw holes by imbedding them so nothing sticks out for injuring your fingers while spinning the handle.

I built a new end cap from solid steel so it is not easly dented like the thin stamped ones original from Wilton.

 

I also replaced the nut, not because it was stripped but because the two ears that keep it from spinning was missing, due to the pins slipping out. I added a set screw with the ends machined down to fit the 1/4 reamed hole, the original pins were pressed in and must have slipped out since the original owner staked the pin in place. I set the vise up in my milling machine and replaced the pin with a threaded insert. Look HERE for how I did it.

 

I replaced the handle with a better steel type, Cold Formed 1144 CRS is the perfect handle material, Wilton uses 11/16 (.687) bar stock, a size that I can not find in 1144 so I bored the spindle out to accept the common 3/4 Diameter size. I peened the custom made knobs in place for a permentant install then added a set of bumpers to save your fingers.

 

I surface ground the anvil so you can add your own scars, it was not bad and did not take much to clean up. I also removed some scars before painting but left most since it is part of the orah of this vise. I primed it with Rust-oleum Self Etching primer and painted it with Rust-oleum Verde Green paint. A very close match to the original paint. The new owner can add his own scars.

 

The $70 for shipping is an estimate only.

The total new parts installed on this vise if purchased in my store http://www.wiltonviseparts.net/  came out to $340.0

Any questions?  Send me a note at this e-mail address:  mountainproduct@gmail.com 

Kevin

 

Vise Specifications: 

Length - 20"  when closed.

Widest dimension of vise - 11"

Height - 8-3/4"

Height from top of jaws to round slider - 4-3/4"

Maxium safe jaw opening - 6" 

Weight 80 lbs

Jaw width - 4-1/2"

Handle  3/4 dia. x 12" long.

Jaw height - 1-1/4"

 

Shipping $65

 Find Similar Products by Category

 Product Reviews

This product hasn't received any reviews yet. Be the first to review this product!

You Recently Viewed...

 

Follow us on

Electronic Check Processing